Atefeh Pourmahdi; Mohebbat Mohebbi; Ashraf Gohari Ardabili; Mehdi Varidi; Mohammad Reza Salahi
Abstract
Introduction: Potato is one of the most consumed and highly nutritious vegetables with high energy, dietary fiber, phytochemicals, vitamins, and minerals which offer great benefit for utilization as functional food ingredient. The dried potato powder can be used in formulation of many foods like soups, ...
Read More
Introduction: Potato is one of the most consumed and highly nutritious vegetables with high energy, dietary fiber, phytochemicals, vitamins, and minerals which offer great benefit for utilization as functional food ingredient. The dried potato powder can be used in formulation of many foods like soups, snacks, sauces, noodles, etc. The foam mat drying involves the dehydration of a thin layer of foam followed by its disintegration in order to obtain a powder which can be easily reconstituted in water when added to other foods. Because of the porous structure of the foamed materials, mass transfer is enhanced leading to shorter drying times and consequently acquiring higher quality in the dried product. Food foams can be considered as biphasic systems where a gas (dispersed phase) is embedded in a continuous liquid phase. The foam properties such as structure, density and stability have important influence on moisture migration during drying and accordingly, the quality of final product. Foams that do not collapse for at least 1h are mechanically or thermally stable for the entire drying process. Response surface methodology (RSM) is a combination of mathematical and statistical techniques which used to investigate the interaction effects of independent variables on responses. There is considerable information on foam-mat dried food powders, but there is not any scientific literature that related to study on foam-mat drying of potato puree. The present research was thus focused on optimizing the foaming conditions (potato puree: gum solution ratio; Arabic gum (AG) concentration as the stabilizer and whipping time [WT]) to minimize foam density (FD) and drainage volume (DV) using RSM. Likewise, choosing a suitable model for thin-layer drying of foam and the effect of different drying temperatures (45, 60 and 80°C) on drying behavior were investigated, and the effective moisture diffusivity and activation energy were calculated. The effects of drying temperatures on water activity (aw) and water binding capacity (WBC) were also investigated.
Material and methods: Fresh potato was purchased from a local market (Mashhad, Iran). Arabic gum was procured from Sigma Chemical Company (USA). For preparation of potato puree, fresh potatoes were washed and peeled by steel knife and were washed again and additional water was taken absolutely and then crushed by Phillips home crusher (600W) with maximum speed for 3 minutes to get a homogeneous puree. Based on preliminary tests, AG solutions were prepared by dissolving a suitable amount of the selected gum powder in distilled water and stirring with a magnetic stirrer to obtain a uniform solution. This solution was refrigerated at 4°C overnight to complete hydration. RSM was used to estimate the main effects of the process variables on FD and DV in potato puree foam. The experiment was established based on a face-centered central composite design (FCCD). The experimental range was chosen on the basis of the results of preliminary tests. The independent variables were consisted of potato puree: gum solution ratio (1:1 –2:1 w/w), AG concentration (0.1–0.9% w/w) and WT (3–9 min). According to the experimental design, to prepare 100 g of samples, appropriate amount of potato puree and AG solution were mixed in a 250-mL beaker. The mixture was then whipped with a kitchen mixer (model no. SM88, Sonny, China) at a maximum speed of 1,500 rpm at ambient temperature during given time which was recommended by Design-Expert software. The density of foamed potato puree was determined in terms of mass over volume and expressed in g/cm3. In order to assess foam stability, the drainage test was performed for 1h. To evaluate drying behavior of the optimized foam, drying was carried out in a batch-type thin-layer dryer at temperatures of 45, 60 and 80°C on 3 mm thickness. Ten thin-layer drying models were evaluated in the kinetics research. The higher value of R2 and lower values of χ2, RMSE and SSE were selected as the basis for goodness of fit. Fick’s diffusion equation for particles with a slab geometry was used for calculation of effective moisture diffusivity. The foamed potato puree spread on a tray was considered as slab geometry. Activation energy was calculated by a simple Arrhenius-type relationship, by plotting the ln (Deff) against the reciprocal of absolute temperature (1/T). Furthermore, the effects of drying temperatures on aw and WBC of powders were investigated.
Results and discussions: The quadratic model was selected as a suitable statistic model for both FD and DV. ANOVA showed that this model is significant for both responses. Moreover, lack-of-fit was not significant for response surface models at 95% confidence level, indicating this model is adequately accurate for predicting responses. The optimum values of variables for best product quality in terms of minimum FD and DV corresponded to potato puree to gum solution ratio 2:1(w/w), AG 0.77% (w/w) and WT 6.80 min. The amount of FD and DV for foam at these optimum conditions were 0.30 g/cm3 and 5 ml, respectively.
The result showed that when the drying temperature increased, the drying time decreased. This was due to the quick removal of moisture at higher temperature. Drying rate (DR) versus moisture content of potato puree foam-mats figure showed that DR was higher during the initial stage as compared with the final stage and foam-mat drying was occurred principally in the constant rate period. Due to the increase in surface area and the porous structure, removal of water from the inner surface of potato puree foam to the outer surface was fast enough to preserve the surface moisture. The rate of movement of moisture from the inner surface to the exposed surface decreased with decreasing moisture content, which indicates that the DR decreased and the falling rate period started. The effective moisture diffusivity varied from 3.286×10-9 to 8.032×10-9 m2/s with activation energy value of 30.97 kJ/mol. Statistical analysis results showed that the Weibull distribution model provide the highest R2 and lowest values of χ2, RMSE and SSE at all drying temperatures. The temperature elevation reduced aw. This is due to the fact that at higher temperatures, the rate of heat transfer to the sample would increase, therefore, it provides greater driving force for moisture evaporation which results the dried foams with reduced aw. Drying temperatures did not show any significant effect on WBC of powders.
Farnaz Hassanzadeh Rad; Fakhri Shahidi; Mohebbat Mohebbi; Mohammad Reza Salahi
Abstract
Introduction: Kilka Fish is one of the most popular seafood products available for aquaculture development. It is a rich source of proteins, vitamins and minerals such as calcium and phosphor. The highly perishable nature of Kilka fish has strongly attracted researchers to find new methods to extend ...
Read More
Introduction: Kilka Fish is one of the most popular seafood products available for aquaculture development. It is a rich source of proteins, vitamins and minerals such as calcium and phosphor. The highly perishable nature of Kilka fish has strongly attracted researchers to find new methods to extend its shelf life. Kilka fish powder can be used in many foods, such as soups, sauces, snacks, etc. Foam-mat drying is a new effective technique has recently gained much attention because it does not suffer from major problems associated with traditional dehydration methods, such as poor rehydration characteristics, unfavorable sensory profile, and long drying time. The main objectives of this study were: (1) to optimize the effective parameters (egg white powder and xanthan gum concentration, and whipping time) on foaming properties of Kilka fish; (2) to study the effects of drying temperature and foam thickness on the drying characteristics and select a suitable model for thin-layer drying of foam; (3) to compute effective moisture diffusivity and activation energy of foam during drying; and (4) to study the effects of drying conditions on moisture content, water activity, hygroscopicity and color of powders and microstructure of dried Kilka fish foams.
Materials and method: Fresh Kilka fish (C. delicatula) was obtained from the Pak Samar Miroud Company (Mazandaran, Iran). Xanthan gum and egg white powders were purchased from Sigma Chemical Company and Gol Powder Company (Golestan Province, Iran) respectively. The Kilka fish skin removed and cleaned, and then crushed using a kitchen blender to obtain a homogeneous and uniform mixture. Based on preliminary tests, xanthan gum solution was prepared by dissolving a suitable amount of the selected gum powder in distilled water and mixed with a magnetic stirrer to obtain a uniform solution. The resulted solution was cooled at 4°C for 18–24h to complete hydration. According to the experimental design, to prepare 100 g of samples, appropriate amount of fish, egg white powder, xanthan gum solution and distilled water were mixed a 250-mL beaker. The mixture was then whipped with a mixer (Gosonic, model No. GHM- 818, 250W, China) with maximum speed at ambient temperature during given time, which was recommended by Design-Expert software version 6.02 (Stat-Ease, Inc., Minneapolis, MN). Foaming conditions, namely amount of egg white powder, xanthan gum and whipping time, optimized using response surface methodology (RSM) for minimizing foam density (FD) and drainage volume (DV). To evaluate drying behavior of the optimized foam, drying was carried out in a batch-type thin-layer dryer at three drying temperatures (45, 60 and 75°C) on 3- and 5-mm thicknesses. Ten thin-layer drying models were evaluated in the kinetics research. The higher values of R2 and lower values of χ2 and RMSE were selected as the basis for goodness of fit. The effective moisture diffusivity was calculated using method of slopes. A Fick’s diffusion model with slab geometry was used to describe the transport of moisture during drying inside a single Kilka fish foam mat. Activation energy was calculated by a simple Arrhenius-type relationship, by plotting the ln (Deff) against the reciprocal of absolute temperature (1/T). The microstructure of the dried fish foam-mats was analyzed by a scanning electron microscope. Finally, the effects of drying conditions on physicochemical properties of fish powder including moisture content, water activity, hygroscopicity and color were investigated.
Results and Discussion: The optimum values of variables for best product quality in terms of minimum FD and DV corresponded to egg white powder 3.67 % (w/w), xanthan gum 0.28% (w/w) and whipping time 8.93 min. The amount of FD and DV for foam at these optimum conditions were 0.92 g/cm3 and 0 ml, respectively. As expected, the increase in drying temperature and decrease in foam load led to acceleration of the dehydration of Kilka fish foam. Based on the statistical tests performed, Weibull distribution model can describe drying behavior of foams for all drying processes. Moreover, Fick’s second law was employed to calculate the effective moisture diffusivity that varied from 7.266×10-8 to 1.31×10-7 m2/s and from 7.404×10-8 to 1.693×10-7 m2/s with activation energy values of 18.201 and 25.615 kJ/mol for foam thicknesses of 3 and 5 mm, respectively. It was noted that the effective moisture diffusivity was increased when the drying temperature increased. Results showed that at the higher thickness, the internal moisture migration occurs along a longer distance rather than lower thickness. Therefore, an increase in moisture diffusivity occurs both with increase in drying temperature and sample thickness. The analysis of scanning electron microscopy (SEM) micrographs showed that there is wide porous structure of dried foams at higher speeds drying. With increasing drying temperature (due to reduction of drying times), combination of adjacent bubbles and therefor, collapse of foam structure occur less. Higher temperature reduced moisture content and aw , and thickness rise increased moisture content and aw under the same thickness and drying temperature, respectively. This is due to the fact that at higher temperatures, the rate of heat transfer to the sample would increase, therefore, it provides greater driving force for moisture evaporation which results the dried foams with reduced moisture content and aw. Moreover, with increasing foam thickness due to increased drying times and probably collapsed structure of foams and therefor weak pore structure, drying was performed difficultly which causes to retain more water in dried foams. Drying conditions had significant effect on hygroscopicity of powders. Results of color investigation showed that in both thicknesses, powder produced at 60°C have higher L* and lower a*.
