Investigating Changes in Color and Shrinkage of Dried Apple Slices Using Image Processing

Document Type : Research Article

Authors

• Javad Safari
• Jafar Hashemi
• Azadeh Ranjbar Nedamani

Biosystem Engineering Department, Sari Agricultural Sciences & Natural Resources University, Sari, Iran

https://doi.org/10.22067/ifstrj.2022.77460.1188

Abstract

Introduction
 Due to the importance of product appearance quality in product grading and the impact of factors such as area, uniformity, and various defects on the product quality, and also, the ability to recognize these features at a very low cost, image processing techniques, is one of the methods used to evaluate food quality. Therefore, in this study, a non-destructive image processing method was used to investigate the factors affecting the color and shrinkage of apple slices during drying.
 
Materials and Methods
 Golden delicious apples were used in this research. The central part of the apple (including the rivet, seeds, and tail) was removed by a kernel separator and sliced into 3, 5, and 7mm thickness and approximately 7 mm diameter slices using a hand slicer without separating the skin. Three temperatures of 60, 70, and 80 °C were used to dry the samples. To determine the moisture content of a sliced apple, the samples were first weighed on a digital scale, then placed in a dryer, and the experiment was continued until the samples reached equilibrium mass. Due to the high importance of moisture ratio in controlling the drying process, moisture rate (MR) and moisture content (MC) were calculated, and samples were taken to investigate the amount of surface shrinkage, general color changes and browning index. After extracting L*, a*, and b* values, total color changes and browning index (to show the intensity of brown color in the product) for all samples before and after drying were calculated and evaluated to describe color changes after drying.
 
Results and Discussion
 The drying kinetics results showed that the drying process significantly depends on the thickness of the samples. According to drying curves, at the early stages of drying, the decrease in humidity occurs more severely and the graph has a steeper slope, but as the process continues and the moisture content of the product decreases, the slope of the curve decreases. In the early stages of drying, due to the presence of water inside the fresh fruit cells, there is a pressure balance between the fruit and the surrounding environment, which causes the fruit to remain swollen. However, as the drying time progressed, contractile stresses are created, which cause superficial shrinkage. In this study, it was observed that increasing the thickness from 3mm to 7mm, reduced the final shrinkage on the surface of apple slices by 11% at 60 °C, 12% at 70 °C, and 13% at 80 °C. After moisture leaves the surface of the product and heat penetrates into the product, moisture begins to leave the product by conducting interstitial convection. When moisture moves to the surface, the mechanical balance and consequently the textural structure of the sample is disturbed due to the creation of different spaces in thickness. According to the results, increasing drying time and thus decreasing the moisture content, increases the percentage of apple shrinkage. On the other hand, at a certain thickness, with increasing temperature, the percentage of shrinkage changes in the thickness of the product decreases. Therefore, at thicknesses of 3, 5, and 7 mm, the increase in temperature from 60°C to 80°C, decreased the amount of shrinkage thickness by 16, 12, and 8%, respectively. It is in higher thicknesses that react with heat and change the color of the fruit due to the Maillard reaction. After complete drying of apple samples, the highest amount of color change was related to the thickness of 7 mm and a temperature of 80°C, which was equal to 1.254. Also, the lowest rate of discoloration of apple slices in a thickness of 3 mm and a temperature of 60 °C was 0.889. The browning index (Bi) in the high thickness of apple slices is less affected by the process temperature due to the increase in moisture level. For this reason, the rate of browning was very low among the experimental samples and the highest rate of browning was related to the thickness of 7 mm and the temperature of 80 °C was 585/2559. Also, the lowest rate of browning of apple slices was observed in the thickness of 3 mm and the temperature of 60 °C was 584.254.
 
Conclusion
 Finally, it was found that the thickness and temperature factors can have an effect on the quality of product during drying process. The results of this study can provide a cheap and fast way to control the quality of fruits during drying and help producers of these products select the main process factors that affect the final quality.
 

Keywords

• Browning
• Drying
• Image processing
• Machine vision
• Shrinkage

Main Subjects

• Food Engineering

©2023 The author(s). This is an open access article distributed under Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source.

References

1. Farahmand, A., Mousavi Baygi, S.F., Taghizadeh, M., & Ziafroughi, M.A. (2015). Quality characteristics of persimmon slices during infrared and hot-air frying. Iranian Food Science and Technology Research Journal, 11(5), 654-664. https://doi.org/10.22067/ifstrj.v0i0.32844
2. Farzan, E., Rahimi, M.R., & Madadi Avargani, V. (2017). Drying kinetic and shrinkage study of a Hawthorn sample in a vibro fluidized bed dryer using an adsorption system in order to control of inlet air humidity. Innovative Food Technologies, 5(1), 107-122. https://doi.org/10.22104/jift.2017.508
3. Gholipour Shahraki, P., & Fazel, M. (2019). Effect of edible coating and time and temperature of drying on properties of dried fig. Iranian Food Science and Technology Research Journal, 15(1), 77-89. https://doi.org/10.22067/ifstrj.v0i0.68897
4. Khorshidi, Y., Kalantari, D., & Asghari, A. (2017). Investigating the influence of drying temperature and air flow velocity on some qualitative specifications of the sliced pear during drying and employment of image processing technique. Journal of Research and Innovation in Food Science and Technology, 6(1), 87-102. https://doi.org/10.22101/JRIFST.2017.05.22.617
5. Mbarek, R., & Mihoubi, D. (2019). Development of physical properties of apple during dehydration. Periodica Polytechnical Chemical Engineering, 63(4), 591-599. https://doi.org/10.3311/PPch.13033
6. Miranda, M., Maureira, H., Rodriguez, K., & Vegalvez, A. (2009). Influence of temperature on the drying kinetics, physicochemical properties, and antioxidant capacity of Aloe Vera (Aloe barbadensis Miller) gel. Journal of Food Engineering, 91(2), 297–304. https://doi.org/10.1016/j.jfoodeng.2008.09.007
7. Mohabbaty, M.H., & Ahmadi Moghadam, P. (2019). Determination of wrinkles, water absorption capacity and color changes of tomato slices during drying process, 2nd International Conference and 6th National Conference on Organic and Conventional Agriculture, Mohaghegh Ardabili University, Ardabil, Iran.
8. Mohebi, S. (2015). Qualitative evaluation of tomato during drying process using different methods. The thesis (MS) submitted to the Graduate for the degree of Master of Science in Mechanical Engineering of Biosystems. Department of Mechanical Engineering of Biosystems. Urmia University. Iran.
9. Mohsenabadi, M. (2012). Effect of some enzymatic browning inhibitors on color change in green olive fruits preprocessing. Master Thesis in Horticulture, Faculty of Agricultural Sciences, University of Guilan, Iran.
10. Momenzadeh, L., Zomorodian, A., & Mowla, D. (2011). Applying artificial neural network for shrinkage prediction of green pea in a microwave assisted fluidized bed dryer. Iranian Journal of Food Science and Technology, 6(4), 277-285. https://doi.org/10.22067/ifstrj.v6i4.9285
11. Naghipour zadeh Mahani, M., & Aghkhani, M.H. (2016). The effect of slicing type on drying kinetics and quality of dried carrot. Journal of Agricultural Machinery, 6(1), 224-235. https://doi.org/10.22067/jam.v6i1.34483
12. Onwude, D.I., Hashim, N., Janius, R., Nawi, N.M., & Abdan, K. (2017). Color change kinetics and total carotenoid content of pumpkin as affected by drying temperature. Italian Journal of Food Science, 29(1), 1-18.
13. Rasouli, M., & Seiiedlou, S. (2012). Brief report: A study of the shrinkage changes and mathematical modeling of garlic (Allium Sativum ) during convective drying. Journal of Agricultural Machinery, 2(1), 67-73. https://doi.org/10.22067/jam.v2i1.14295
14. Roosata pour, O.R., Maftoon Azad, N., & Khalu Ahmadi, A. (2015). Study of drying kinetics and shrinkage of potato slice in a parallel flow dryer. Journal of Food Science and Technology(Iran), 12(47), 109-122.
15. Sabbaghi, H., Ziaiifar, A.M., & Kashaninejad, M. (2018). Fractional conversion modeling of color changes in apple during simultaneous dry-blanching and dehydration process using intermittent infrared irradiation. Iranian Food Science and Technology Research Journal, 14(2), 383-397. https://doi.org/10.22067/ifstrj.v0i0.62293
16. Satorabi, M., Salehi, F., & Rasouli, M. (2021). Effect of edible coatings on the color and surface changes of apricot slices during drying in infrared system. Iranian Journal of Food Science and Technology, 18(112), 21-30. https://doi.org/10.52547/fsct.18.112.21
17. Seyedabadi, E. (2017). Numerical modeling of simultaneous mass and heat transfer with shrinkage effect during convective drying of banana. Ph.D. Dissertation. Faculty of Agriculture. Ferdowsi University of Mashhad. Iran.
18. Tabaei, A.,  Hazbavi, I., & Shahbazi, F. (2020). Modeling and optimization of persimmon drying using response surface methodology. Iranian Journal of Food Science and Technology, 17(98), 109-119. https://doi.org/10.29252/fsct.17.01.10
19. Taghinezhad, E., Kaveh, M., Jahanbakhshi, A., & Golpour, I. (2020). Use of artificial intelligence for the estimation of effective moisture diffusivity, specific energy consumption, color and shrinkage in quince drying. Journal of Food Process Engineering, 43(4), 1-12. https://doi.org/10.1111/jfpe.13358
20. Torki Harchegan, M., Sadeghi, M., Ghanbarian, D., & Moheb, A. (2016). Dehydration characteristics of whole lemons in a convective hot air dryer. Iranian Journal of Chemistry & Chemical Engineering-International English Edition, 35(3), 65-73. https://doi.org/10.30492/ijcce.2016.22060
21. Turkmen, F., Karasu, S., & Karadag, A. (2020). Effects of different drying methods and temperature on the drying behavior and quality attributes of cherry laurel fruit. Processes, 8(7), 761-786. https://doi.org/10.3390/pr8070761
22. Khorshidi, Y. (2016). Investigation of drying kinetics of pear fruit slices in a thin layer dryer and their dimentional changes by image processing techniques.Sc thesis of Mechanics of Bio-System Engineering. Sari Agricultural Sciences and Natural Resources University. Iran.
23. Yuan, Y., Tan, L., Xu, Y., Yuan, Y., & Dong, J. (2019). Numerical and experimental study on drying shrinkage-deformation of apple slices during process of heat-mass transfer. International Journal of Thermal Sciences, 136, 539-548. https://doi.org/10.1016/j.ijthermalsci.2018.10.042
24. Zia Alhagh, S.H.R. (2010). Determination of the optimum conditions for preparing and drying of potato slices. Journal of Food Research (University of Tabriz), 19(1)(2), 23-36.