Determination of rheological properties of tomato under quasi static loading conditions

Document Type : Research Article

Authors

• Mersad Ghorbannejad Shahroudi ¹
• Abdollah Golmohammadi ¹
• Davood Kalantari ²

¹ Department of Biosystems Engineering, Faculty of Agriculture and Natural Resources, University of Mohaghegh Ardabili, Iran.

² Department of Mechanical Bio-system, Faculty of Agricultural Engineering, University of Agricultural Sciences and Natural Resources Sari, Iran.

https://doi.org/10.22067/ifstrj.v1395i0.55948

Abstract

Introduction: Mechanical damages in agricultural products cause wastes directly and indirectly. Bruise damage due to quasi static load is one of the most important reasons of fresh fruit quality loss. Agricultural crops undertake many mechanical loads and physical damages during different stages of harvesting and post-harvest such as handling, transport, storage and processing. In many cases imported loads cause mechanical damages and cellular wall rupture and this rupture leads to perturbation of natural cellular interchanges. This object is one of the important problems of modelling and experimental studies in Biosystems engineering sciences. Tomato is one of the most important horticultural products and a widely produced products in the world. Larg amounts of tomato products are destroyed during the different stages of harvesting, transport and packaging. To study the viscoelastic behavior of agricultural crops, rheology science is used which is the science of biological materials deformation and flow ability under affection of loads at different times. For prediction and classification of materials behavior under different conditions of stress and strain, different rheological models are used. These models include different combinations of metallic body (spring) and Newtonian liquid body (dashpot) that illustrate complex behavior of agricultural products. Determining of factors that affect deformation value of tomato, lead to reduction of product waste.

Materials and methods: In this study, the effect of some important parameters such as static loading at three levels (2, 6 and 10 N), storage temperature at two levels (4 and 25 ˚C), loading at two directions for two cultivars (Supper-Beta and Petoerly-CH), were studied on deformation value. Samples were handy harvested at approximate ripeness level (reddish pink) from greenhouse and transported to the Lab. Some physical properties (mass, volume, major and minor diameters, height, sphericity coefficient, surface area) were measured. Samples were subjected to compressive loading using university made apparatus. The Experiments were performed in a fifteen-day period, at two different conditions, ones at temperature 4 ˚C and the other at environmental temperature 25 ˚C, using factorial test in form of completely randomized design. The first test was performed under constant load of 6 N in two directions of fruit axials (Z and Y directions), The second test was performed in three levels 2 and 10 N in direction of calyx face. By indicator, deformation value of tomatoes at 2, 4, 7, 10, and 15 days after loading was investigated. The third test was performed under constant loads of 15 N and deformation values of samples were recorded every 10 mins during a 60-minute period.

Results and conclusions: The Results showed at temperature 25 ˚C, with increasing load from 2 up to 10 N, deformation value of the product would be increased about 65%. Increase of deformation value indicates the effect of loading time for products such as tomatoes. This phenomenon can be a result of bulk density ratio reduction of product during the storage, because biochemical reactions are effective in fruit ripening, activating the destructive enzymes of cellular wall during the storage, softening and color changes. Maintaining fruits in direction of calyx face leads to lower deformation in comparison with 90 degrees proportion to calyx. This phenomenon is because of tomato tissue, its tissue in direction of calyx is harder and stiffer of normal direction, because of being flower. By reducing temperature from 25 to 4 ˚C, at constant load of 6N, deformation was decreased about 40%. With decreasing temperature, viscosity of biologic products would be increased and cellular walls get brittle and tissue stiffness increase. Therefore, it seems logical that deformation value of product at lower temperature decreases. Super-Beta cultivar had more durability in comparison with Petoerly-CH against compressive static loads. Under constant loading conditions, General Kelvin rheological model was considered suitable to estimate the strain versus time.

Keywords

• Variety
• compression loading
• Rheological Properties
• deformation

References

Afkari Sayah, A., & Minaee, S., 2009, Foundations and mechanical lesions Farm products. Publications SID unit Ardabil province. (In Farsi)

Allende, A., Desmet, M., Vanstreels, E., & Nicola, M., 2004, Micromechanical and geometrical properties of tomato skin related to differences in puncture injury susceptibility. Postharvest Biology and Technology, 34, 131–141.

Broniowska, K., Gladysezewska, B., & Ciupal, A. 2012, Effect of storage time and temperature on Poisson ratio of tomato fruit skin, Journal of Agro-physic 26, 39-44.

Galedar, M., Tabatabaeefar, A., Jafari, A., Sharifi, A., O’Dogherty, M. J., Rafee, S., & Richard, G., 2008, Effects of moisture content and level in the crop on the engineering properties of alfalfa stems. Journal of Bio-systems. 101(2), 199-208.

Hassan, H., Alhamdan, M., & Elansari, M., 2005, Stress relaxation of dates at Khalal and Rrutab stages of maturity. Journal of Food Engineering. 6, 439-445.

Hosseini, Hoshyar, S., Fatemian, H., & Elkhush, B., 2010, The effects of impact forces from a fall on the biophysical properties of the tomato. Journal of Food Science and Nutrition (In Farsi)

Hyde, M., Baritelle, L., & Varith, J., 2001, Fruit and vegetable conditioning to improve impact bruise threshold. In: Proceedings of the 6th International Symposium on Fruit, Nut and Vegetable Production Engineering. Journal of Potsda Germany 11–14.

Kader A, A., & Rolle, R. S., 1987, The role of post-harvest management in assuring the quality and safety of horticultural produce, FAO Agricultural Service Bulletin

Mazaheri, Tehrani, M., Morteza, A., Zeyalhagh, H., & Ghandi, A., 2007, Tomato processing. Publication of border, (In Farsi)

Moghimi, A., & Saidi Rad, M., 2010, Cherry viscoelastic behavior under constant strain. Sixth National Congress of Agricultural Engineering and Mechanization machines (In Farsi)

Mohammadi Aylar, S., Minaee, S., & Afkari, Sayah, A., 2010 Mechanical properties of tomato under compressive loads during different stages of post-harvest handling. Iranian Journal of Bio-systems engineering.

Mohsenin, N. N., 1986, Physical properties of plant and animal materials, Vol. 1. Gordon and Breach Science Publication.

Myhan, R., Bialobrzewski, I., & Markowski, M., 2012, An approach to modeling the rheological properties of food materials. Journal of Food Engineering. 111, 351-359.

Rao, M, Rizvi, H., & Datta, K., 2005, Engineering properties of foods (3rd Ed.). Taylor and Francis Group. USA.

Rong, W., Qunying, J., & Deqiang, W., 2004, On the mechanical damage of grape using finite element analysis. An ASAE/CSAE Meeting presentation.

Schoorl, D., & Hplt, J., 1977, The effects of storage time and temperature on the bruising of Jonathan, Delicious and Granny Smith apples, Journal of Texture Studied. 8, 409-416.

Stroshine, R., 1994, Physical properties agricultural materials food products. Course Manual. Purdue University Press, West Lafayette. Indiana. USA

Tiback, E., Langton, M., Oliveria, J., & Ahme, L., 2014, Mathematical modeling of the viscosity of tomato, broccoli and carrot purees under dynamic conditions. Journal of Food Engineering, 124, 35-42.

Wu, T., & Abbott, J. A., 2002, Firmness and force relaxation characteristics of tomatoes stored intact or as slices, Postharvest Biology and Technology, 24, 59-68