Preparation of Biopolymer Based on Agar Extracted from Persian Gulf Red Algae Acanthophora and Evaluation of Its Properties

Document Type : Research Article

Authors

• Parisa Dianat ¹
• Mahdi Haji Abdolrasouli ²
• Morteza Yousefzadi ³

¹ Department of Marine Biology, University of Marine Sciences and Technology, Hormozgan University, Bandar Abbas, Iran

² Department of Chemical Engineering, Faculty of Chemical and Petroleum Engineering, Hormozgan University, Bandar Abbas, Iran

³ Department of Biology, Faculty of Basic Sciences, University of Qom, Qom, Iran

https://doi.org/10.22067/ifstrj.2023.78025.1196

Abstract

Introduction
 Consumer demand for healthy food free of chemical preservatives and environmental concerns with plastic packaging environments are analyzed, which can be replaced by aquatic environments that can be contaminated, for the development of bio-based packaging materials. Natural polymers have the ability to be biodegradable due to the presence of oxygen or nitrogen atoms in their main polymer chain compared to the dominant carbon-carbon bonds in fossil-based polymers. Among the various biopolymers used to prepare multilayer films, polysaccharides are considered as the main components of the film due to their abundance and non-toxicity. These films generally have good mechanical strength, moderate physical properties, and most importantly, are edible and easily degradable. However, they are very brittle and hydrophilic, and these properties are undesirable in food packaging applications. Among polysaccharides, agar, commercially extracted from seaweed, is one of the most common and widely studied base materials. Agar is insoluble in cold water, but soluble in water at 90-100°C. When making an agar film, the solution and casting surface must be kept above the agarose gel setting temperature to avoid premature gelation. Compared to other biopolymers, agar is more stable at low pH and high temperature. This thermoplastic and biocompatible polysaccharide creates films with high mechanical strength, transparency and moderate barrier properties to carbon dioxide and oxygen, and most importantly, it is edible and easily biodegradable. Mixing agar with other polymers such as polyvinyl alcohol (PVA) and polyethylene improves the mechanical, thermal and biodegradability properties of bio composites. The main goal of this study is to make biofilms for use in packaging industries with agar polymer extracted from macroalgae species Acanthophora sp. Agar was extracted by sodium hydroxide/heating method and the film was prepared in combination with industrial polymer PVA and glycerol.
 
Materials and Methods
 To make biofilms based on agar polymer, firstly, optimization of agar polymer extraction from macroalgae species Acanthophora sp. was done by sodium hydroxide/heating method, and in the next step, total phenolic compounds and the amount of soluble protein in extracted agar were measured. In the next step, glycerol with 30% by weight was used as a softener and PVA polymer with a weight ratio of 25% to the dry weight of agar powder was used to make bio composite by solvent casting method, in order to strengthen the mechanical and physical properties of bio composites. Characterization tests of the prepared composites included: XRD, FTIR and Tensile test. Laboratory tests include; The percentage of solubility in water and degree of swelling for all bio-composites were evaluated to determine the optimal physical properties of bio-films.
 
Results and Discussion:
he results showed that; 15% extraction efficiency was obtained for sodium hydroxide/heating pretreatment method. The results of measuring the amount of total phenolic compounds in agar solution extracted by sodium hydroxide/heating method showed that the number of phenolic compounds in agar solution was 0.077 ± 0.004 in terms of mg of gallic acid/g of agar. The results of measuring the amount of protein in extracted agar determined by Bradford method showed that the agar solution contains 0.040 ± 0.019 mg/ml of protein. A decrease in the swelling rate and an increase in the water solubility of the agar bio composite occurred with the addition of glycerol and PVA polymer. The results of the tensile test showed that the addition of glycerol, a small hydrophilic molecule, to the agar bio composite leads to a decrease in the elastic modulus and an increase in flexibility. Adding PVA to agar/glycerol biofilm caused a decrease in the amount of elastic modulus and percentage of flexibility, which is the main factor of this phenomenon, the low values of elastic modulus and flexibility of PVA. Finally, the results confirm the use of these coatings for packing fruits and vegetables in tropical regions by increasing their shelf life for at least 5 days at 25°C.

Keywords

• Bioplastic
• Bio-polymer
• Packing
• Polysaccharide
• PVA

Main Subjects

• Food Technology

©2023 The author(s). This is an open access article distributed under Creative Commons Attribution 4.0 International License (CC BY 4.0), which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source.

References

1. Abdullah, A.H.D., Fikriyyah, A.K., Putri, O.D., & Asri, P.P.P. (2019). Fabrication and characterization of poly lactic acid (PLA)-starch based bioplastic composites. IOP Conference Series: Materials Science and Engineering, https://doi.org/10.1016/j.polymertesting.2023.108000
2. Arham, R., Salengke, S., Metusalach, M., & Mulyati, M. (2018). Optimization of agar and glycerol concentration in the manufacture of edible film. International Food Research Journal, 25(5), 1845-1851.
3. Basumatary, K., Daimary, P., Das, S.K., Thapa, M., Singh, M., Mukherjee, A & .Kumar, S. (2018). Lagerstroemia speciosa fruit-mediated synthesis of silver nanoparticles and its application as filler in agar based nanocomposite films for antimicrobial food packaging. Food Packaging and Shelf Life, 17, 99-106. https://doi.org/10.1016/j.fpsl.2018.06.003
4. da Rocha, M., de Souza, M.M., & Prentice, C. (2018). Biodegradable films: An alternative food packaging [Interview]. Elsevier. https://doi.org/10.1016/B978-0-12-811516-9.00009-9
5. Fakhouri, F.M., Costa, D., Yamashita, F., Martelli, S.M., Jesus, R.C., Alganer, K., Collares-Queiroz, F.P., & Innocentini-Mei, L.H. (2013). Comparative study of processing methods for starch/gelatin films. Carbohydrate Polymers, 95(2), 681-689. https://doi.org/10.1016/j.carbpol.2013.03.027
6. Fakhouri, F.M., Martelli, S.M., Bertan, L.C., Yamashita, F., Mei, L.H.I., & Queiroz, F.P.C. (2012). Edible films made from blends of manioc starch and gelatin–Influence of different types of plasticizer and different levels of macromolecules on their properties. LWT, 49(1), 149-154. https://doi.org/10.1016/j.lwt.2012.04.017
7. Ganesan, A.R., Shanmugam, M., Palaniappan, S., & Rajauria, G. (2018). Development of edible film from Acanthophora spicifera: Structural, rheological and functional properties. Food Bioscience, 23, 121-128. https://doi.org/10.1016/j.fbio.2017.12.009
8. Haghighi, H., Gullo, M., La China, S., Pfeifer, F., Siesler, H.W., Licciardello, F., & Pulvirenti, A. (2021). Characterization of bio-nanocomposite films based on gelatin/polyvinyl alcohol blend reinforced with bacterial cellulose nanowhiskers for food packaging applications. Food Hydrocolloids, 113, 106454. https://doi.org/10.1016/j.foodhyd.2020.106454
9. Hasan, M., & Rahmayani, R.F.I., (2018). Bioplastic from chitosan and yellow pumpkin starch with castor oil as plasticizer. IOP Conference Series: Materials Science and Engineering,(Vol. 333,p, 012087). IOP Publishing.
10. Hernández, V., Ibarra, D., Triana, J.F., Martínez-Soto, B., Faúndez, M., Vasco, D.A., Gordillo, L., Herrera, F., García-Herrera, C., & Garmulewicz, A. (2022). Agar biopolymer films for biodegradable packaging: A reference dataset for exploring the limits of mechanical performance. Materials, 15(11), 3954. https://doi.org/10.3390/ma15113954
11. Hii, S.-L., Lim, J.-Y., Ong, W.-T., & Wong, C.-L. (2016). Agar from Malaysian red seaweed as potential material for synthesis of bioplastic film. Journal of Engineering Science and Technology, 11, 1-15.
12. Hong, S.-I., Cho, Y., & Rhim, J.-W. (2021). Effect of agar/AgNP composite film packaging on refrigerated beef loin quality. Membranes, 11(10), 750. https://doi.org/10.3390/membranes11100750
13. Kumar, S., Boro, J.C., Ray, D., Mukherjee, A., & Dutta, J. (2019). Bionanocomposite films of agar incorporated with ZnO nanoparticles as an active packaging material for shelf life extension of green grape. Heliyon, 5(6), e01867. https://doi.org/10.1016%2Fj.heliyon.2019.e01867
14. Kumar, S., Shukla, A., Baul, P.P., Mitra, A., & Halder, D. (2018). Biodegradable hybrid nanocomposites of chitosan/gelatin and silver nanoparticles for active food packaging applications. Food Packaging and Shelf Life, 16, 178-184. https://doi.org/10.1016/j.fpsl.2018.03.008
15. Kumar, V., & Fotedar, R. (2009). Agar extraction process for Gracilaria cliftonii (Withell, Millar, & Kraft, 1994). Carbohydrate Polymers, 78, 813-819. https://doi.org/10.1016/j.carbpol.2009.07.001
16. Lee, J.-S., Choi, I., & Han, J. (2021). Mathematical modeling of cinnamon (Cinnamomum verum) bark oil release from agar/PVA biocomposite film for antimicrobial food packaging: The effects of temperature and relative humidity. Food Chemistry, 130306. https://doi.org/10.1016/j.foodchem.2021.130306
17. Madera-Santana, T., Freile-Pelegrín, Y., & Azamar-Barrios, J. (2014). Physicochemical and morphological properties of plasticized poly (vinyl alcohol)–agar biodegradable films. International Journal of Biological Macromolecules, 69, 176-184. https://doi.org/10.1016/j.ijbiomac.2014.05.044
18. Madera-Santana, T.J., Robledo, D., & Freile-Pelegrín, Y. (2011). Physicochemical properties of biodegradable polyvinyl alcohol–agar films from the red algae Hydropuntia cornea. Marine Biotechnology, 13(4), 793-800. https://doi.org/10.1016/j.ijbiomac.2020.02.158
19. Madera‐Santana, T., Misra, M., Drzal, L., Robledo, D., & Freile‐Pelegrin, Y. (2009). Preparation and characterization of biodegradable agar/poly (butylene adipate‐co‐terephatalate) composites. Polymer Engineering & Science, 49(6), 1117-1126. https://doi.org/10.1002/pen.21389
20. Marichelvam, M.K., Jawaid, M., & Asim, M. (2019). Corn and rice starch-based bio-plastics as alternative packaging materials. Fibers, 7(4), 32. https://doi.org/10.3390/fib7040032
21. Marichelvam, M., Manimaran, P., Sanjay, M., Siengchin, S., Geetha, M., Kandakodeeswaran, K., Boonyasopon, P., & Gorbatyuk, (2022). Extraction and development of starch-based bioplastics from Prosopis juliflora Plant: Eco-friendly and sustainability aspects. Current Research in Green and Sustainable Chemistry, 5, 100296. https://doi.org/10.1016/j.crgsc.2022.100296
22. Martínez-Sanz, M., Gómez-Mascaraque, L.G., Ballester, A.R., Martínez-Abad, A., Brodkorb, A., & López-Rubio, A. (2019). Production of unpurified agar-based extracts from red seaweed Gelidium sesquipedale by means of simplified extraction protocols. Algal Research, 38, 101420. https://doi.org/10.1016/j.algal.2019.101420
23. Mathew, S., Mathew, J., & Radhakrishnan, E. (2019). Polyvinyl alcohol/silver nanocomposite films fabricated under the influence of solar radiation as effective antimicrobial food packaging material. Journal of Polymer Research, 26(9), 1-10. https://doi.org/10.1007/s10965-019-1888-0
24. Mensi, F. (2019). Agar yield from R-phycoerythrin extraction by-product of the red alga Gracilaria verrucosa. Journal of Applied Phycology, 31(1), 741-75 https://doi.org/10.1007/s10811-018-1533-z.
25. Nguyen, T.T., Nguyen, T.-T.H., Pham, B.-T.T., Van Tran, T., Bach, L.G., Thi, P.Q.B., & Thuc, C.H. (2021). Development of poly (vinyl alcohol)/agar/maltodextrin coating containing silver nanoparticles for banana (Musa acuminate) preservation. Food Packaging and Shelf Life, 29, 100740. https://doi.org/10.1016/j.fpsl.2021.100740
26. Orsuwan, A., Shankar, S., Wang, L.-F., Sothornvit, R., & Rhim, J.-W. (2016). Preparation of antimicrobial agar/banana powder blend films reinforced with silver nanoparticles. Food Hydrocolloids, 60, 476-485. https://doi.org/10.1016/j.foodhyd.2016.04.017
27. Rhim, J.-W. (2011). Effect of clay contents on mechanical and water vapor barrier properties of agar-based nanocomposite films. Carbohydrate Polymers, 86(2), 691-699. https://doi.org/10.1016/j.carbpol.2011.05.010
28. Rhim, J., Wang, L., & Hong, S. (2013). Preparation and characterization of agar/silver nanoparticles composite films with antimicrobial activity. Food Hydrocolloids, 33(2), 327-335. https://doi.org/10.1016/j.foodhyd.2013.04.002
29. Samadi, N., Sabzi, M., & Babaahmadi, M. (2018). Self-healing and tough hydrogels with physically cross-linked triple networks based on Agar/PVA/Graphene. International Journal of Biological Macromolecules, 107, 2291-2297. https://doi.org/10.1016/j.ijbiomac.2017.10.104
30. Sasuga, K., Yamanashi, T., Nakayama, S., Ono, S., & Mikami, K. (2017). Optimization of yield and quality of agar polysaccharide isolated from the marine red macroalga Pyropia yezoensis. Algal Research, 26, 123-130. https://doi.org/10.1016/j.algal.2017.07.010
31. Shankar, S., & Rhim, J.-W. (2017). Preparation and characterization of agar/lignin/silver nanoparticles composite films with ultraviolet light barrier and antibacterial properties. Food Hydrocolloids, 71, 76-84. https://doi.org/10.1016/j.foodhyd.2017.05.002
32. Shankar, S., Teng, X., & Rhim, J.-W. (2014). Properties and characterization of agar/CuNP bionanocomposite films prepared with different copper salts and reducing Carbohydrate Polymers, 114, 484-492. https://doi.org/10.1016/j.carbpol.2014.08.036
33. Soleimani, S., Yousefzadi, M., Nezhad, S.B.M., Pozharitskaya, O.N., & Shikov, A.N. (2022). Evaluation of fractions extracted from Polycladia myrica: biological activities, UVR protective effect, and stability of cream formulation based on it. Journal of Applied Phycology, 34(3), 1763-1777. https://doi.org/10.1007/s10811-022-02705-2
34. Sousa, A. M., Alves, V., Morais, S., Delerue-Matos, C., & Gonçalves, M.P. (2010). Agar extraction from integrated multitrophic aquacultured Gracilaria vermiculophylla: evaluation of a microwave-assisted process using response surface methodology. Bioresource technology, 101(9), 3258-3267. https://doi.org/10.1016/j.biortech.2009.12.061
35. Spierling, S., Knüpffer, E., Behnsen, H., Mudersbach, M., Krieg, H., Springer, S., Albrecht, S., Herrmann, C., & Endres, H.-J. (2018) Bio-based plastics-A review of environmental, social and economic impact assessments. Journal of Cleaner Production, 185, 476-491. https://doi.org/10.1016/j.jclepro.2018.03.014
36. Sudhakar, M.P., Magesh Peter, D., & Dharani, G. (2021). Studies on the development and characterization of bioplastic film from the red seaweed (Kappaphycus alvarezii). Environmental Science and Pollution Research, 28(26), 33899-33913. https://doi.org/10.1007/s11356-020-10010-z
37. Suryanegara, L., Fatriasari, W., Zulfiana, D., Anita, S.H., Masruchin, N., Gutari, S., & Kemala, T. (2021). Novel antimicrobial bioplastic based on PLA-chitosan by addition of TiO₂ and ZnO. Journal of Environmental Health Science and Engineering, 19(1), 415-425. https://doi.org/10.1007/s40201-021-00614-z
38. Susilawati, S., Rostini, I., Pratama, R.I., & Rochima, E. (2019). Characterization of bioplastic packaging from tapioca flour modified with the addition of chitosan and fish bone gelatin. World Scientific News, 135, 85-98.
39. Wongphan, P., & Harnkarnsujarit, N. (2020). Characterization of starch, agar and maltodextrin blends for controlled dissolution of edible films. International Journal of Biological Macromolecules, 156, 80-93. https://doi.org/10.1016/j.ijbiomac.2020.04.056
40. Wulandari, D., Hermiyati, I., Iswahyuni, I., & Tawarniate, A.Z. (2022). Production and characterization of gelatin from rabbit bone as bioplastics material by acid pre-treatment. World Rabbit Science, 30(1): 83-93.
41. Yusoff, N.H., Pal, K., Narayanan, T., & de Souza, F.G. (2021). Recent trends on bioplastics synthesis and characterizations: Polylactic acid (PLA) incorporated with tapioca starch for packaging applications. Journal of Molecular Structure, 1232, 129954. https://doi.org/10.1016/j.molstruc.2021.129954