با همکاری انجمن علوم و صنایع غذایی ایران

نوع مقاله : مقاله پژوهشی

نویسندگان

گروه مهندسی بیوسیستم، دانشکده کشاورزی، دانشگاه بوعلی سینا، همدان.

چکیده

در این پژوهش اثر متغیرهای خشک‌کردن به شیوه هوای ‌گرم با اعمال پیش تیمار مایکروویو شامل دمای هوا، سرعت هوا و مدت زمان مایکروویو بر ویژگی‌های فیزیکی (چروکیدگی و چگالی واحد)، مکانیکی (مقاومت به نفوذ) و حرارتی (ضریب انتشار مؤثر رطوبت و انرژی مصرفی خشک‌کردن) قرص فشرده تولید شده از پودر گوجه‌فرنگی مورد بررسی قرار گرفت. فرآیند خشک‌کردن نمونه‌ها در پنج سطح دمایی 40، 50، 60، 70 و °C80، پنج سطح سـرعت هـوا 5/0، 1، 5/1، 2 و m/s 5/2 و پنج زمان مختلف فرآیند مایکروویو صفر (بدون اعمال مایکروویو)، 4، 8، 12 و s 16 در توان ثابت W 90 صورت گرفت. تجزیه و تحلیل آماری داده‌ها و بهینه‌سـازی فرآیند خشک‌کردن با استفاده از روش سطح پاسخ انجام شد. نتایج نشان داد که استفاده از پیش­تیمار مایکروویو سبب کاهش زمان خشک‌کردن و انرژی مصرفی آن و همچنین اثر معنی­داری بر بهبود خواص فیزیکی و مکانیکی قرص­های فشرده تولید شده داشت. افزایش دمای هوای خشک‌کردن بر ضریب انتشار مؤثر رطوبت و چروکیدگی اثر مثبت و بر انرژی ویژه مصرفی خشک‌کردن، مقاومت به نفوذ و بر چگالی واحد اثر منفی داشت. با افزایش مدت زمان مایکروویو مقدار ضریب انتشار مؤثر رطوبت افزایش و با کاهش آن مقدار چروکیدگی محصول کاهش یافت. نقطه بهینه خشک‌کردن قرص فشرده تولید شده از پودر گوجه‌فرنگی در دمای °C50، سرعت هوا m/s 1 و مدت زمان مایکروویو s 4 به‌دست آمد. خشک‌کردن تحت شرایط کمترین دما (°C40) وکمترین زمان مایکروویو (s 4) سبب بهبود خواص فیزیکی و مکانیکی قرص فشرده گردید.

کلیدواژه‌ها

عنوان مقاله [English]

Optimization of tomato compressed tablet production based on physical, mechanical and thermal properties in a hot air condition with microwave pretreatment

نویسندگان [English]

  • Manoochehr Rashidi
  • Reza Amiri Chayjan
  • Ali Ghasemi

Department of Biosystems Engineering, Faculty of Agriculture, Bu-Ali Sina University, Hamedan, Iran.

چکیده [English]

Introduction: Tomato is one of the most valuable sources of minerals and vitamins supply in the human diet. Low shelf life of tomato and its short shelf life with inadequate processing facilities lead to heavy financial losses. Therefore, preserving and processing of tomato are of the commercial importance. Drying is one of the preferred methods for tomato preservation. Dried tomato products including half tomatoes, tomato slices and tomato powder, have many consumptions, compared with other tomato products. Among dried tomato products, tomato powder has a particular market. Powder production is an alternative method to extend the shelf life of foods. Usually the fruit powder is very dry, humidity absorber and has too much volume. Therefore, during storage, transportation and administration, it requires special care and heavy packaging which increase the cost. To overcome these problems, compression of the fruit powder in tablet form could be a proper solution. Tablet making of fruit powder has gained much popularity due to its ease of use, storage, transportation and product formulation. After the tablet making process, the pills contain high moisture contentwhich makes them un-suitable for transportation and storage. So, in order to prevent the tablets corruption and maintain their quality, tablet drying is one of the important steps after the tablet making process. The drying process is an important operation that affects the quality and final price of the product. Different drying methods play an important role in protecting foodstuffs. However, the effect of different drying methods on the quality of some foodstuffs is not clear.
 
Materials and methods: In this research, after the preparation of fresh tomatoes, the primary moisture content of tomatoes was determined using hot air oven method. Then, using blanching method, the tomatoes were peeled and samples were cut using a sharp razor in thicknesses of 3 mm. Tomato slices were dried using a semi-industrial dryer in a hot air at 50 °C at an air speed of 1 m/s. Dried tomato slices were powdered using a grinder. In order to homogenize the particle size, the tomato powder was sieved by a 50 mesh (Cavity size 0.5 mm) sample. Suitable moisture content to create sufficient adhesion between the particles of tomato powder was selected at %23 d.b. Water and fructose were used as a bonding agent. The process of producing tomato spherical tablets was performed by a hydraulic press. Drying tests of wet compressed tablets were performed immediately after the end of the tabletting process using a hot air drying machine with microwave pre-treatment. In this study, the effect of drying variables,through using of  microwave pre-treatment along with hot air, including air temperature in five levels (40, 50, 60, 70 and 80 °C), air velocity at five levels (0.5, 1, 1.5, 2, and 2.5 m/s) and the duration of microwave application at five levels (zero (without microwave), 4, 8, 12, and 16 s) on physical properties (shrinkage and unit density), mechanical (penetration resistance) and thermal (Effective moisture diffusivity and energy consuming drying) of compact pomegranate produced from tomato powder were studied. Statistical analysis of data and optimization of drying process were performed using response surface method and central composite design.
 
Results and discussion: Results showed that effect of air temperature and duration of microwave pretreatment on all variables of compressed tomato tablets were significant in hot air dryers with microwave pre-treatment. Increasing temperature and time of microwave pre-treatment increased the effective moisture diffusivity and shrinkage of the final product. The temperature of the air inlet to the dryer had a negative effect on the resistance to penetration, the unit density and the specific energy consumption of the drying process. Drying under lower temperature conditions and less time for microwave pre-treatment resulted in an increase in the desirability of the drying process

کلیدواژه‌ها [English]

  • Optimization
  • Microwave pretreatment
  • Tomato compressed tablet
  • Drying
احمدی قویدلان، م و امیری چایجان، ر. (1396). استفاده از روش سطح پاسخ جهت بهینه‌سازی خشک‌کردن فندق در بسترسیال مادون‌قرمز. پژوهش های صنایع غذایی، 26(4): 639-657.‎
احمدی قویدلان، م و امیری چایجان، ر. (1396). بهینه‌سازی خشک‌کردن مغز فندق در خشک‌کن مادون قرمز با پیش‌تیمار مایکروویو به کمک روش سطح پاسخ. علوم و صنایع غذایی ایران، 14(64): 178-165.
خاکباز حشمتی، م و سیفی مقدم، ا. (1396). بررسی تکنیک متناوب مایکروویو-هوای گرم بر خواص کیفی و تغذیه‌ای برگه‌های کیوی خشک شده. پژوهش های صنایع غذایی، 27(1): 111-126.‎
زرین‌نژاد، م و امیری چایجان، ر. (1395). تعیین شرایط بهینه فرآیند خشک کردن پسته در خشک کن مایکروویو بستر سیال. مجله علوم و صنایع غذایی، 13(57): 13-24.
سالک، ف و قنبریان، د. (1395). اثر دما و رطوبت بر برخی از ویژگی‌های مکانیکی دانه سویا تحت بارگذاری شبه استاتیک. نشریه پژوهش های صنایع غذایی، 4(26): 705-714.
صفری، م، امیری‌چایجان، ر و علائی، ب. (1396). مدل‌سازی برخی خواص حرارتی و فیزیکی مغز بادام در خشک‌کن خلائی مادون قرمز با پیش‌تیمار میکروویو. مهندسی زراعی، 39(1): 21-37.
ندیم، ز و احمدی، ا. (1395). بررسی برخی خواص رئولوژیکی توت فرنگی پوشش‌دهی شده با متیل سلولز. ماشین‌های کشاورزی، 6(1): 153-162.
Adiba, B. D., Salem, B., Nabil, S., & Abdelhakim, M. (2011). Preliminary characterization of food tablets from date (Phoenix dactylifera L.) and spirulina (Spirulina sp.) powders. Powder Technology, 208(3), 725-730.
And, G. L., & Barrett, D. M. (2006). Influence of Pre‐drying Treatments on Quality and Safety of Sun‐dried Tomatoes. Part I: Use of Steam Blanching, Boiling Brine Blanching, and Dips in Salt or Sodium Metabisulfite. Journal of Food Science, 71(1), S24-S31.
Artnaseaw, A., Theerakulpisut, S., Benjapiyaporn, C. 2010. Development of a vacuum heat pump dryer for drying chilli. Biosystems engineering, 105(1), 130-138.
Aziz, M., Yusof, Y., Blanchard, C., Saifullah, M., Farahnaky, A., & Scheiling, G. (2018). Material Properties and Tableting of Fruit Powders. Food Engineering Reviews, 1-15.
Burubai, W., Akor, A., Igoni, A., Uyate, Y. 2007. Effects of temperature and moisture content on the strength properties of African nutmeg (Monodora myristica). Bulgarian Journal of Agricultural Science, 13(6), 703.
da Silva, L. B., Queiroz, M. B., Fadini, A. L., da Fonseca, R. C., Germer, S. P., & Efraim, P. (2016). Chewy candy as a model system to study the influence of polyols and fruit pulp (açai) on texture and sensorial properties. LWT-Food Science and Technology, 65, 268-274.
Demiray, E., Tulek, Y., & Yilmaz, Y. (2013). Degradation kinetics of lycopene, β-carotene and ascorbic acid in tomatoes during hot air drying. LWT-Food Science and Technology, 50(1), 172-176.
Figiel, A. (2010). Drying kinetics and quality of beetroots dehydrated by combination of convective and vacuum-microwave methods. Journal of Food Engineering, 98(4), 461-470.
Ghasemi, A., & Chayjan, R. A. (2018). Optimization of Pelleting and Infrared-Convection Drying Processes of Food and Agricultural Waste Using Response Surface Methodology (RSM). Waste and Biomass Valorization, 1-19.
Kantrong, H., Tansakul, A., & Mittal, G. S. (2014). Drying characteristics and quality of shiitake mushroom undergoing microwave-vacuum drying and microwave-vacuum combined with infrared drying. Journal of food science and technology, 51(12), 3594-3608.‏
Liu, F., Cao, X., Wang, H., & Liao, X. (2010). Changes of tomato powder qualities during storage. Powder Technology, 204(1), 159-166.
Marfil, P., Santos, E., & Telis, V. (2008). Ascorbic acid degradation kinetics in tomatoes at different drying conditions. LWT-Food Science and Technology, 41(9), 1642-1647.
Nualkaekul, S., Deepika, G., & Charalampopoulos, D. (2012). Survival of freeze dried Lactobacillus plantarum in instant fruit powders and reconstituted fruit juices. Food research international, 48(2), 627-633.
Ong, M., Yusof, Y., Aziz, M., Chin, N., & Amin, N. M. (2014). Characterisation of fast dispersible fruit tablets made from green and ripe mango fruit powders. Journal of Food Engineering, 125, 17-23.
Purkayastha, M. D., Nath, A., Deka, B. C., & Mahanta, C. L. (2013). Thin layer drying of tomato slices. Journal of food science and technology, 50(4), 642-653.
Samuelsson, R., Larsson, S. H., Thyrel, M., & Lestander, T. A. (2012). Moisture content and storage time influence the binding mechanisms in biofuel wood pellets. Applied energy, 99, 109-115.
Shamsudin, I., Anuar, M., & Tahir, S. (2012). Compaction of sweet potato (Ipomoea Batatas L.) and stevia rebaudiana food powders. Particulate Science and Technology, 30(2), 136-144.
Śledź, M., Nowacka, M., Wiktor, A., & Witrowa-Rajchert, D. (2013). Selected chemical and physico-chemical properties of microwave-convective dried herbs. Food and Bioproducts Processing, 91(4), 421-428.
Tumuluru, J. S., Wright, C. T., Hess, J. R., & Kenney, K. L. (2011). A review of biomass densification systems to develop uniform feedstock commodities for bioenergy application. Biofuels, Bioproducts and Biorefining, 5(6), 683-707.
Widodo, R. T., & Hassan, A. (2015). Compression and mechanical properties of directly compressible pregelatinized sago starches. Powder Technology, 269, 15-21.
Wongsiriamnuay, T., & Tippayawong, N. (2015). Effect of densification parameters on the properties of maize residue pellets. Biosystems Engineering, 139, 111-120.
Workneh, T. S., & Oke, M. O. (2013). Thin layer modelling of microwave-convective drying of tomato slices. International journal of food engineering, 9(1), 75-90.
Yusof, Y., Mohd Salleh, F., Chin, N., & Talib, R. (2012). The drying and tabletting of pitaya powder. Journal of Food Process Engineering, 35(5), 763-771.
Zarein, M., Samadi, S. H., & Ghobadian, B. (2015). Investigation of microwave dryer effect on energy efficiency during drying of apple slices. Journal of the Saudi Society of Agricultural Sciences, 14(1), 41-47.
Zea, L. P., Yusof, Y. A., Aziz, M. G., Ling, C. N., & Amin, N. A. M. (2013). Compressibility and dissolution characteristics of mixed fruit tablets made from guava and pitaya fruit powders. Powder technology, 247, 112-119.
Zhang, Z., Song, H., Peng, Z., Luo, Q., Ming, J., & Zhao, G. (2012). Characterization of stipe and cap powders of mushroom (Lentinus edodes) prepared by different grinding methods. Journal of Food Engineering, 109(3), 406-413.
CAPTCHA Image