با همکاری انجمن علوم و صنایع غذایی ایران

نوع مقاله : مقاله پژوهشی فارسی

نویسندگان

گروه مهندسی مواد و طراحی صنایع غذایی، دانشگاه علوم کشاورزی و منابع طبیعی گرگان.

چکیده

بافت از مهم‌ترین ویژگی‌های کیفی میوه‌ها طی خشک‌کردن است. آزمون تجزیه و تحلیل پروفیل بافت (TPA) برای بافت‌های بیولوژیکی ناهمگن بسیار مناسب است و همبستگی مناسبی با ارزیابی حسی نشان می‌دهد. در این پژوهش، بافت برش‌های سیب آب‌زدایی‌شده با پرتودهی مادون قرمز در سه دمای سطحی 70، 75 و 80 درجه سانتی‌گراد مطالعه شد. محصول در سه ضخامت 5، 9 و 13 میلی‌متر تا دستیابی به سطح نهایی رطوبت برابر با 15، 20 و 25 درصد بر حسب وزن مرطوب خشک شد. سپس، آزمون تجزیه و تحلیل پروفیل بافت (TPA) با فشردن تا 50 درصد تغییر شکل با دستگاه بافت‌سنج انجام‌گرفت. ارزیابی حسی برش‌های خشک‌شده نیز از نظر بافت مطلوب و پذیرش کلی صورت پذیرفت. جهت تجزیه و تحلیل آماری از طرح کاملاً تصادفی (CRD) در قالب فاکتوریل (33) و آزمون دانکن با سطح اطمینان 95 درصد استفاده شد. نتایج نشان داد که خشک‌کردن تا سطوح رطوبتی مورد مطالعه موجب کاهش سختی و چسبندگی و افزایش فنریت، انسجام، شاخص صمغی، قابلیت جویدن و قابلیت ارتجاعی نسبت به بافت سیب خام شد. پذیرش کلی و بافت مطلوب در نمونه‌های خشک‌شده در شدت کم تبخیر (دمای کمتر، ضخامت کمتر و سطح رطوبتی بیشتر) ملاحظه گردید. سختی بافت برش سیب در این شرایط برابر با 685/7 ±177/695 گرم بود. با افزایش ضخامت برش‌ها، انسجام و فنریت کاسته شد و در نتیجه قابلیت جویدن به‌طور معنی‌داری کاهش‌یافت. طی خشک‌کردن رفتار بافت از ویسکوالاستیک (سختی اولیه بالاتر و انسجام، فنریت و قابلیت ارتجاعی پایین‌تر) به الاستیک و سپس به پلاستیک یا شیشه‌ای تغییر کرد.  

کلیدواژه‌ها

عنوان مقاله [English]

Textural profile analysis (TPA) of dried apple slices using infrared radiation with intermittent heating method

نویسندگان [English]

  • Hassan Sabbaghi
  • Aman Mohammad Ziaiifar
  • Mahdi Kashani-Nejad

Food Processing Engineering Department, Gorgan University of Agricultural Sciences & Natural Resources.

چکیده [English]

Introduction: Fruits and their products in the dried form are good sources of vitamins, energy and minerals. However, during the process of drying or dehydration there are changes in quality parameters in dried products. Texture is one of the most important quality attributes of fruits during drying, reflecting their mechanical and microstructural properties. Apple is perishable fruit. Drying of apple is very important because of High losses are experienced during the seasonal glut. A novel process in food industry is the simultaneous infrared dry blanching and dehydration operation (SIRDBD) with intermittent heating method (radiation at constant temperature) exerted on fruits and vegetables that is known to enhance the quality of the final product. In the food industry, end-products must achieve a compromise between several properties, including sensory, sanitary and technological properties. Prediction of changes in texture during drying could be helpful in a better process control and improvement in overall acceptability of a dried snack food. The change of the elastic or viscoelastic texture of the fresh apples to rigid, fragile and brittle in the apple chips were evaluated by instrumental and sensory methods. Many attempts have been made to describe the viscoelastic behavior of dehydrated fruits and vegetables. Maxwell’s or compression models are limited to homogeneous, isotropic materials. In contrast, texture profile analysis (TPA) is more suitable for heterogeneous biological materials and shows a good correlation with organoleptic evaluation. Typical TPA parameters are including hardness, adhesiveness, springiness, cohesiveness, gumminess, chewiness and resilience. In this research, for the first time, textural analysis of dried apple slices by infrared heating at different temperatures and different moisture levels was performed. Finally, the optimum texture and overall acceptance of the product are described according to the instrumental analysis.
 
Materials and methods: Apples (Golden Delicious variety) were purchased from a local market and kept in 0°C±1°C and relative humidity ranging from 90% to 95%. Before every thermal processing, the apple specimens were picked up from the cold storage and then they were put into use after reaching the ambient temperature. The samples were skinned manually and then cut into slices with different thicknesses of 5mm, 9mm and 13mm, all 20mm in diameter. The sliced apples were immediately subjected to simultaneous blanching and infrared drying. The texture of dehydrated apple slices using infrared radiation at three surface temperatures of 70, 75 and 80 °C were studied. The product in three thicknesses was dried to achieve a moisture level of 15, 20 and 25% wet weight basis. Then, texture profile analysis (TPA) was carried out to 50% compression strain using texture analyzer. The sensory evaluation of dried slices was also considered for desire texture (Good mouth feels texture, lack of hard tissue, no shrinkage) and overall acceptance (The final acceptability of the product in terms of total sensory properties including color, texture, flavor and aroma) by 10 professional panelists. For statistical analysis, a completely randomized design (CRD) was used in a factorial form (33) and Duncan test with 95% confidence level.
 
Result & Discussion: The results showed that drying to studied moisture levels reduced the hardness and adhesiveness and increased springiness, cohesiveness, gumminess, chewiness and resilience in comparison with raw apple tissue. Hardness of samples dried at higher temperature was higher due to rapid removal of moisture which might have caused collapse of capillary voids inside the product. Due to shrinkage samples became denser and thus a larger fracture force was to be expected. As water content increases (i.e., higher RH) water plasticizes the cell walls and the material and product becomes softer and more pliable, thus hardness decreases. The increase of hardness could be because the rapid mass transfer that damaged the membrane and cell structure of the fruits during drying. Another important factor responsible for the increase of hardness of finish-dried samples is the low final moisture content when compared with other samples. High temperature drying method enables samples to reach low moisture content at relatively short duration and therefore the product with harder texture was obtained. The maximum value of adhesiveness was observed for fresh apples, which could be attributed to the high moisture and sugar content. Adhesiveness decreased with moisture loss, indicating the availability of free water on the sample surface. A significant decrease in springiness following high-temperature drying could be attributed to the glass transition phenomenon and changes from elastic to plastic behavior. In the period of softening, cohesiveness increased with moisture loss. Hardening caused a decrease in cohesiveness depending on the drying temperature. Gumminess is the energy required to disintegrate a semisolid food to a state of readiness for swallowing. High values of gumminess revealed “firm” and “crisp” with a cell rupture mode of tissue failure and lowest values of gumminess could be classified as “soft”.  At the end of drying and with apple hardening, chewiness increased to values equal or above initial chewiness, indicating that a larger amount of energy is needed to masticate dried apples. Resilience had increasing with moisture loss. By increasing the thickness of the slices, the cohesiveness and springiness decreased and hence chewiness significantly decreased. The overall acceptance and desire texture in dried samples was observed at lower water evaporation rate conditions (lower temperatures, lower thickness and higher moisture content). In these conditions, the hardness of apple slices tissue was equal to 695.177 ± 7.685 grams. During drying of the apple, textural behavior was varied from the viscoelastic (higher initial hardness, with cohesiveness, springiness and lower resilience) to elastic and then to plastic or glassy.

کلیدواژه‌ها [English]

  • Drying
  • Texture Profile Analysis
  • Apple
  • Infrared irradiation
  • Sensory evaluation
Acevedo, N. C., Briones, V., Buera, P., & Aguilera, J. M. (2008). Microstructure affects the rate of chemical, physical and color changes during storage of dried apple discs. Journal of Food Engineering, 85(2), 222-231.
Barrett, D. M., Beaulieu, J. C., & Shewfelt, R. (2010). Color, flavor, texture, and nutritional quality of fresh-cut fruits and vegetables: desirable levels, instrumental and sensory measurement, and the effects of processing. Critical Reviews in Food Science and Nutrition, 50(5), 369-389.
Bourles, E., Mehinagic, E., Courthaudon, J., & Jourjon, F. (2009). Impact of vacuum cooking process on the texture degradation of selected apple cultivars. Journal of Food Science, 74(9).
Chong, C. H., Figiel, A., Law, C. L., & Wojdyło, A. (2014). Combined drying of apple cubes by using of heat pump, vacuum-microwave, and intermittent techniques. Food and Bioprocess Technology, 7(4), 975-989.
Chong, C. H., Law, C. L., Cloke, M., Abdullah, L. C., & Daud, W. R. W. (2008). Drying kinetics, texture, color, and determination of effective diffusivities during sun drying of Chempedak. Drying Technology, 26(10), 1286-1293.
Cuccurullo, G., Giordano, L., Albanese, D., Cinquanta, L., & Di Matteo, M. (2012). Infrared thermography assisted control for apples microwave drying. Journal of Food Engineering, 112(4), 319-325.
Falade, K., & Aworh, O. (2004). Adsorption isotherms of osmo-oven dried African star apple (Chrysophyllum albidum) and African mango (Irvingia gabonensis) slices. European Food Research and Technology, 218(3), 278-283.
Food and Agriculture Organization, Dried fruit, in: www.fao.org/3/a-au111e.pdf or http://www.fao.org/3/V5030E/V5030E0j.html
Funebo, T., Ahrne, L. l. a., Kidman, S., Langton, M., & Skjöldebrand, C. (2000). Microwave heat treatment of apple before air dehydration–effects on physical properties and microstructure. Journal of Food Engineering, 46(3), 173-182.
Khin, M. M., Zhou, W., & Yeo, S. Y. (2007). Mass transfer in the osmotic dehydration of coated apple cubes by using maltodextrin as the coating material and their textural properties. Journal of food Engineering, 81(3), 514-522.
Kotwaliwale, N., Bakane, P., & Verma, A. (2007). Changes in textural and optical properties of oyster mushroom during hot air drying. Journal of Food Engineering, 78(4), 1207-1211.
Krokida, M. K., Karathanos, V. T., & Maroulis, Z. B. (2000). Compression analysis of dehydrated agricultural products. Drying technology, 18(1-2), 395-408.
Kupongsak, S., & Tan, J. (2006). Application of fuzzy set and neural network techniques in determining food process control set points. Fuzzy Sets and Systems, 157(9), 1169-1178.
Liu, Y., Zhu, W., Luo, L., Li, X., & Yu, H. (2014). A mathematical model for vacuum far-infrared drying of potato slices. Drying Technology, 32(2), 180-189.
Lopez, J., Uribe, E., Vega-Galvez, A., Miranda, M., Vergara, J., Gonzalez, E., & Di Scala, K. (2010). Effect of air temperature on drying kinetics, vitamin C, antioxidant activity, total phenolic content, non-enzymatic browning and firmness of blueberries variety Neil. Food and Bioprocess Technology, 3(5), 772-777.
Loredo, A. B. G., Guerrero, S. N., Gomez, P. L., & Alzamora, S. M. (2013). Relationships between rheological properties, texture and structure of apple (Granny Smith var.) affected by blanching and/or osmotic dehydration. Food and Bioprocess Technology, 6(2), 475-488.
Maity, T., Raju, P., & Bawa, A. (2012). Effect of freezing on textural kinetics in snacks during frying. Food and Bioprocess Technology, 5(1), 155-165.
Martynenko, A., & Janaszek, M. A. (2014). Texture changes during drying of apple slices. Drying Technology, 32(5), 567-577.
Mayor, L., & Sereno, A. (2004). Modelling shrinkage during convective drying of food materials: a review. Journal of Food Engineering, 61(3), 373-386.
Nishinari, K., Kohyama, K., Kumagai, H., Funami, T., & Bourne, M. C. (2013). Parameters of texture profile analysis. Food Science and Technology Research, 19(3), 519-521.
Nowak, D., & Lewicki, P. P. (2005). Quality of infrared dried apple slices. Drying Technology, 23(4), 831-846.
Perrot, N., Ioannou, I., Allais, I., Curt, C., Hossenlopp, J., & Trystram, G. (2006). Fuzzy concepts applied to food product quality control: A review. Fuzzy Sets and Systems, 157(9), 1145-1154.
Toğrul, H. (2006). Suitable drying model for infrared drying of carrot. Journal of Food Engineering, 77(3), 610-619.
Vega-Galvez, A., Ah-Hen, K., Chacana, M., Vergara, J., Martinez-Monzo, J., Garcia-Segovia, P., Di Scala, K. (2012). Effect of temperature and air velocity on drying kinetics, antioxidant capacity, total phenolic content, colour, texture and microstructure of apple (var. Granny Smith) slices. Food Chemistry, 132(1), 51-59.
Velickova, E., Winkelhausen, E., & Kuzmanova, S. (2014). Physical and sensory properties of ready to eat apple chips produced by osmo-convective drying. Journal of Food Science & Technology, 51(12), 3691-3701.
Zhu, Y., Pan, Z., McHugh, T. H., & Barrett, D. M. (2010). Processing and quality characteristics of apple slices processed under simultaneous infrared dry-blanching and dehydration with intermittent heating. Journal of Food Engineering, 97(1), 8-16.
CAPTCHA Image